You have no items in your shopping cart.
Leader in the ACP Industry
Armour MCP Test Report
Alstrong MCP FR A2 class test reports
| Test Parameters | Test Methods | Units | Results |
|---|---|---|---|
| Panel Coating Thickness | ASTM D 7091 | μm | 25 - 27 (Two Coat) |
| Panel Thickness | Visual | mm | 4.00 |
| Panel Weight | Visual | Kg/m2 | 4.1 |
| Panel Density | ASTM D-1505 | g/cm3 | 1.0 |
| Tensile Strength | ASTM E 8 | MPa | 50.6 |
| 0.2% Proof Stress. | ASTM E 8 | MPa | 45.0 |
| % Elongation | ASTM E 8 | % | 9.2 |
| Peel Strength Top Side | ASTM D 903 | N/mm | 8.5 |
| Peel Strength Back Side | ASTM D 903 | N/mm | 6.8 |
| Flexure Strength | ASTM D 790 | MPa | 65.5 |
| Flexural Modulus | ASTM D 790 | MPa | 14115 |
| Punch Shear Test | ASTM D 732 | N/mm2 | 20.5 |
| Test Parameters | Test Methods | Units | Results |
|---|---|---|---|
| Lacquering (PVDF) |
Chemicals | -- | KYNAR 500 PVDF, Passes |
| Taber abrasion test CS-17 Wheels, 1 kg load, 1000 cycles | ASTM D 4060 | mg | 23 |
| Adhesion (Cross Hatch) dry wet (500 C, 20 min) | ASTM D 3359 | B | 5B |
| Adhesion (Cross Hatch) | ASTM D 3359 | B | 5B |
| Hardness - Pencil |
ASTM D 3363 | B/H | H |
| Water Absorption Test | ASTM D 570 | % | 0.6 |
| Glass at 60 |
ASTM D 523 | -- | 35 |
| Impact Test (Front & Reverse) |
ASTM D 2794 | Joules | 22J, Passes |
| Bending Strength |
ASTM D 522 | -- | Passes |
*Bending of Armour minimum radius required 1000 mm
*All test result are for 0.5 mm coil thickness
Alstrong is the leader in ACP industry
Alstrong has established its new plant with two new manufacturing lines for Class A ACP and Class A MCP in Dubai, UAE to cater Middle Eastern, African and European market. The total installed capacity of Dubai plant is 3 Million square meter per annum
| Test Parameters | Test Methods | Units | Results |
|---|---|---|---|
| Skin thickness Top coil thickness Bottom coil thickness | Visual | mm | 0.60 0.60 |
| Tensile strength Top coil thickness Bottom coil thickness | ASTM E 8 | MPa | 1.76.5 175.0 |
| Elongation Top coil thickness Bottom coil thickness | ASTM E 8 | % | 7.65 6.98 |
| Panel Weight | ASTM E 8 | MPa | 170.0 165.5 |
| Test Parameters | Test Methods | Units | Results |
|---|---|---|---|
| Reaction to Fire | EN 13501 -1 | -- | A2- s1, d0 |
| Test Parameters | Test Methods | Units | Results |
|---|---|---|---|
| Sound Absorption Factor |
ISO 354 | -- | 0.05 |
| Sound Transmission Loss | ASTM E90 | dB | 25 |
| Test Parameters | Test Methods | Units | Results |
|---|---|---|---|
| Thermal Resistance |
ASTM C 1363 | m²K/W | 0.24 |
| Linear Thermal Expansion | ASTM d 696 | mm/M/ 100°C | 2.4 |
| Temperature Resistance |
°C | (-) 50°C to 80°C |
*All test result are for 0.5 mm coil thickness
SGS Report
PCS-gross heat of combustion [MJ/kg or MJ/m2]
FIGRA-Fire growth rate index used for classification purposes[W/s]
for Class A2 and Class B FIGRA=FIGRA 02MJ
for Class C and Class D FIGRA=FIGRA 02MJ
LFS - Lateral flame spread[m]
THR500s - Total heat released within 600 s[mJ]
SMOGRA-Smoke growth rate [m2/s2]
THR500s - Total smoke production within 600 s[m2]
According to the test result, the classification for the panel is GB 8624 A (A2-s, d0)
Flame retardant board and high flame retardant board shall comply with the below requirement.
According to the test result, the submitted sample comply with the flammability requirement of GB/T 22412-2016 clause 5.6 and table 6
| Item | Requirment | ||
|---|---|---|---|
| Flame Retardant | High Flame Retardant | ||
| Core gross heat of combustion /(MJ/kg) | s15 | s15 | |
| Board combustion performance level | B1(B) | ||
| Board combustion performance additional information / classification | SMOGRA | s1 | |
| Burning droplets/ particles grades | dO | ||
The test result release to the behaviour of the test specimens of a product under the particular conditions of the test are not intended to be the sole criterion for assessing the potential fire hazard of the product in use.
This classification report does not represent type approval or certification of the product.
*All test result are for 0.5 mm coil thickness
Fire Behaviour - A2
FIRE TEST FOR BUILDING MATERIAL - CLASSIFICATION
Building materials fire behavior has been classified into the following categories in accordance with the global standard.
| Building Class Material | Designation | ||
|---|---|---|---|
| Class A | |||
| A1 | Non-combustible material | ||
| A2 | |||
| Class B | |||
| B1 | Not easily flammable | ||
| B2 | Flammable | ||
| B3 | Easily flammable | ||
Fuel : to burn
Air : to supply oxygen
Heat : to start & discontinue combustion
Fire can be extinguished by removing any one element of the fire triangle - Fuel + Air + Heat
We are removing the fuel by having only metal core and no burnable plastic core. Thus, breaking the fire triangle.
Digital Marketing Partner - Auxano Graphic Designs © 2018 Alstrong UAE All Rights Reserved.